Low Heat Release Yellow Resistance Crystal Clear Epoxy Resin For
Contemporary Coffee Table Casting
Product description
Epoxy Resin 400-4AB is a TOP coat Food grade epoxy resin that cures
under normal and low temperature conditions. It has good leveling,
natural defoaming, low viscosity, high hardness and high strength.
It can be cured at room temperature or by heating. Dedicated to
crystal drop board, marble board, 3D floor insulation, metal floor,
kitchen countertop, resin coating, high hardness coating on any
surface; and other electronic parts, moisture-proof potting, secret
masking, etc.
Features
High water clear appearance
High hardness
High gloss
Easy application
Easy to clean
Advantages
High water clear appearance
High hardness
High gloss
Easy application
Easy to clean
Conditions of Use
1) Ratio: A:B=100:33(weight ratio)
A: B=100:50(Volume ratio)
2) Hardening conditions: 25℃×8H-10H OR 50℃×1.5H(2g)
3) Pot life: 25℃×20min(100g)
TIP:
MC400-4AB and MC00-5AB different Pot life
At 30 degrees Celsius:
MC400-5AB: 10-20 kg, used up in 15 minutes
MC400-4AB: 8-10 kg, used up in 15 minutes
At 20-25 degrees Celsius:
MC400-5AB: 10-20 kg, used up in 15 minutes
MC400-4AB: 10-15 kg, used up in 15 minutes
At 10-15 degrees Celsius:
MC400-5AB: 20-30 kg, used up within 20 minutes
MC400-4AB: 15-20 kg, used up within 20 minutes
Use method
1. Working environment: Please keep the plastic container clean. A,
B components are strictly according to the weight ratio, accurately
weighed, and stir it evenly along the inner wall of the container
clockwise until it is used for 3-5 minutes.
2. According to the operating time and amount of glue deployment,
to avoid waste. When the temperature is lower than 15 °C, please
pre-heat the A glue to 30 °C and then adjust the rubber, easy to
operate (low temperature, A glue will thicken ); After use must
seal the lid, to avoid the product due to moisture absorption
scrapped.
3. When the relative humidity is more than 85%, the surface of the
cured product can easily absorb the moisture in the air to form a
white mist. Therefore, when the relative humidity is more than 85%,
it is not suitable for room temperature curing. It is recommended
to use the heating and curing.
4. The lid must be sealed after use to avoid the product being
scrapped due to moisture absorption.
Hardened property
1) Hardness: shore D <90
2) Withstand voltage: KV/mm 22
3) Bending strength: Kg/mm2 23
4) Volume resistance: Ohm3 1x10*15
5) Surface resistance: Ohmm2 5X10*15
6) Thermal conductivity: W/M.K 0.61
7) Lure power loss: 1KHZ 0.42
8) Heat distortion temperature: ℃ 80
9) Water absorption: % <0.15
10) Compressive strength: Kg/mm2 13.4
The above performance data is typical data measured in a laboratory
environment with a temperature of 25°C and a humidity of 70%. It is
for customer reference only.
Lab Equipment
Caution
1, The operating environment should be ventilative and should keep
away from fire. Closely sealed after use.
2, Avoid eye contact, in case of contact, wash with plenty of water
and get medical attention immediately.
3, If contact skin, wrap with clean cloth or paper, and wash it
with water and soap.
4, Keep away from children.
5, Please take a trial before application to avoid usage mistake.
Storage And Shelf Life
1, Store at the temperature of 25°C or cool and dry place. Avoid
from sunlight, high temperature or high humidity environment.
2, Use up as soon as possible when opened. It is strictly forbidden
to expose to the air for a long time after it is opened to avoid
affecting the quality of the products. The shelf life is six months
in the room temperature of 25°C.
